Buy less equipment, use less power: That's a proposition network managers can get behind, and it's what Cisco promises with the new power management features in its Catalyst 3750-X stackable access switch.
As this exclusive Clear Choice test demonstrates, Cisco makes good on that promise with StackPower, a means of pooling power among switches in a stack. Testing validated that StackPower can cut both capital and operational costs.
The switches also support PoE+, a new method of lighting up power-hungry Web cameras, 802.11n Wi-Fi access points, and other devices requiring more juice than the old PoE standard can supply.
We verified full PoE+ operation on 48 switch ports concurrently, and ran the switch through a rigorous battery of conformance tests developed by Sifos Technologies. Those tests turned up only minor issues, none of which should affect interoperability.
The 3750-X offers other new features, such as MACSec encryption and Smart Operations deployment software, on top of what is already a lengthy features list. We focused on the new switch's power management capabilities.
StackPower offers a means of pooling power supplies within a stack and making wattage available to any switch as needed. The advantages include savings on power and power supplies; redundancy with no extra footprint; and a prioritization scheme that first cuts power to lower-priority ports in case a power supply fails.
StackPower connections are conceptually similar to the StackWise Plus links supported in earlier Catalyst 3750 switches, with multiple switches connected in a ring topology. The switches continue to share power if a connection fails, something we verified in testing. (While StackPower works only with the new X series switches, StackWise Plus works between newer and older Catalyst 3750 models.)
Up to four Catalyst 3750-X switches can form a StackPower ring. This is fewer than the nine switches supported in StackWise Plus. However, a nine-switch StackPower unit still can be formed through the use of an XPS-2200, an external redundant power system that connects to the switches using a star topology. We did not test the XPS-2200.
Cost savings is StackPower's most obvious benefit. Given the importance network managers typically place on high availability, it's not uncommon to find redundant power supplies in every switch throughout the enterprise. With StackPower, it's possible to purchase fewer power supplies and still obtain N+1 redundancy for power supplies in a ring (or N:1 redundancy if using the XPS-2000).
For example, if each of three switches in a stack consumes 200 watts, the aggregate power draw is 600 watts. With 715-watt power supplies, full N+1 redundancy would involve six power supplies at $1,000 each, supplying up to 4,290 watts.
In contrast, the StackPower could run the same stack with as few as two 715-watt power supplies. That's a savings of four power supplies or $4,000, and a rated capacity of only 1,430 watts, with the same level of redundancy.
While many other stackable switches support an external redundant power supply, this is the first system we're aware of that provides internal redundancy, and thus requires no extra rack space.
The new power system also boosts resiliency through strict and redundant configuration modes that allocate and reserve only as much power as is required. If one or more power supplies fails, the switch will begin shedding power using a three-tier prioritization scheme. This prioritization could be used, for example, to protect power over Ethernet (PoE) ports by first shutting down other ports.
Another new feature is support for the new PoE+ standard. As described in the IEEE 802.3at specification, PoE+ offers up to 30 watts per switch port, nearly double the 15.4 watts supplied by first-generation PoE equipment.
As far as we could determine, the Catalyst 3750-X is among the first switches to concurrently support PoE+ on all 48 ports without requiring an external power supply. We put that claim to the test using the PowerSync analyzer from Sifos Technologies. (Sifos provides PoE and Ethernet PHY automated test and measurement solutions for network equipment and semiconductor manufacturers, test labs, system integrators, field service and IT departments.)
Using the Sifos analyzers, we assessed PoE+ in two ways. First, we verified that the 3750-X could indeed supply 30 watts on all 48 gigabit Ethernet ports at the same time. The switch passed this test without complaint.
Second, we ran the full Sifos protocol conformance suite to measure how faithfully the new Cisco switch adheres to the IEEE 802.3at spec. Of hundreds of tests in this suite, the 3750-X failed just three, all relatively minor. Cisco says it's issuing a fix for these issues in new software scheduled for release in late August.
The first failure involved one field in the LLDP (logical link discovery protocol) packets that devices use to identify one another. This is a gray area in the 802.3at specification and might not be a problem in production networks.
Cisco uses a legacy value in the power-via-MDI (medium dependent interface) type-length-value field of LLDP packets rather than one of two values given by the IEEE standard. This has no impact on Cisco's PoE+ devices. It could be a problem for other vendors' powered devices – but only if those devices expect a specific return value. Even in that case, the device could still use PoE+ but might not support some extended features.
The second failure involved the time needed to go into a fully powered-up state. The IEEE spec expects power-supplying equipment to take no longer than 400 millisec between the instant of deciding to apply power and being fully powered up. The Cisco switch took slightly longer, as high as 465 millisec, on a few switch ports. Other ports were within the 400-millisec limit.
The higher times are probably due to Cisco's use of IOS to handle power-management decisions as opposed to the PoE+ logic itself in dedicated power injectors. The 400-millisec limit is in place to minimize the risk of a device being unplugged during power-up and has no impact on interoperability.
The final failure had to do with the way the switch restricts current as it powers up. This is mostly to protect the switch in case a powered device demands too much current. The IEEE spec requires the switch to go into a current-limited state for at least 50 millisec but no longer than 75 millisec. The Sifos analyzer reported that a few Cisco switch ports remained in a current-limited state for at least 100 millisec. This issue is unlikely to have any impact on device interoperability.
Above and beyond these minor issues, network managers may need to reconsider power and cooling budgets when rolling out PoE+.
A large-scale 802.3at deployment requires a lot of power – in this test, 1,440 watts just for PoE+ alone on 48 ports, with additional wattage needed for other switch functions. With all that power in use, PoE+ installations also throw off far more heat than their PoE predecessors. Older wiring closets with poor ventilation unfortunately are all too common in enter- prise networks; these aren’t good candidates for supporting many ports of PoE+.
As a final test of the Catalyst 3750-X's power management features, we measured power consumption in various configurations, both idle and fully loaded.
We used three tools for this: a Fluke 335 TrueRMS clamp meter for the power measurement itself; the Sifos analyzer to load up PoE+ ports; and a Spirent TestCenter traffic generator/analyzer to blast the switch with line-rate traffic on all ports.
With a single 1,150-watt power supply, one switch consumed around 141 watts idle and 150 watts fully loaded. These figures are virtually identical to those measured on a Cisco Catalyst 3570-E in Network World's early 2008 access switch comparison.
Power consumption was only about 50% higher, not double, when the same single power supply drove two 3750-X switches in a stack. And with PoE+ enabled and line rate traffic offered to 48 gigabit Ethernet ports, a two-switch stack equipped with two power supplies consumed about 1,800 watts (the slight differences with and without traffic are within the Fluke instrument's measurement resolution). As noted, PoE+ alone consumes 1,440 watts of the total. The two switches use the remaining 364 watts, or around 182 watts each, comfortably within Cisco's rated maximum of 246 watts per switch.
With these new power features, the Catalyst 3750-X extends an already lengthy features list. StackPower and PoE+ provide an innovative way to pool power and to support power-hungry new devices.
Newman is a member of the Network World Lab Alliance and president of Network Test, an independent test lab and engineering services consultancy. He can be reached at firstname.lastname@example.org.
Network World gratefully acknowledges the vendors that supplied key test bed infrastructure to make testing possible. Sifos Technologies, a vendor of power over Ethernet and Ethernet PHY test sets, supplied its PowerSync analyzers and considerable engineering support. Spirent Communications supplied its Spirent TestCenter traffic generator/analyzer with both 10-gigabit and gigabit Ethernet test ports. And Fluke Corp. supplied its Fluke 335 TrueRMS clamp meter for power measurement.
In some ways, Google is like every other large enterprise. It had the typical defensive security...
The university's hijacked vending machines and 5,000 other IoT devices were making seafood-related DNS...
The U.S. government reportedly pays Geek Squad technicians to dig through your PC for files to give to...
Microsoft today announced that the open source Kubernetes container management platform is now...
Satellite worksites can cause big headaches for tech pros tasked with keeping company assets secure. We...
At RSA 2017, security expert Konstantin Karagiannis (CTO at BT North America) gives Network World an...
Broadband internet has opened up almost unlimited possibilities for commerce, distance learning, civic...