Few of us think about filters until we take our car in for its 50,000-mile service. Looking at the service invoice, there\u2019s an air filter, oil filter, fuel filter, cabin air filter, transmission filter\u2026\nSheesh, how many filters does this thing have?!\nWe may also think about them at family dinners. All of us have at least one relative who could use a filter. I\u2019m looking at you, Aunt Sondra.\nBut most of the time, filters are out of sight, out of mind. Most people are gobsmacked when they discover we carry a dozen or more around in our pockets \u2013 and they\u2019re not for pocket lint, Snapchat or Instagram.\nThe basics of RF filters\nFilters, like antennas, are an increasingly important part of the networking mix.\nThe rapid growth in mobile wireless data and 4G LTE networks has created an ever-increasing need for new frequency bands, and combining bands through carrier aggregation, to accommodate wireless traffic. While 3G networks used only about five frequency bands, LTE networks now use over 40, and this number will grow even more with the advent of 5G.\nConnected devices must transmit cellular signals, Wi-Fi, Bluetooth and GPS across multiple frequency bands while avoiding interference. We might immediately think of smartphones, but the same is true of shark fins mounted atop a car\u2019s roof, cellular base stations, radar and communications systems, and industrial, scientific or medical applications connected to the Internet of Things (IoT). This is where filters come in.\nWith a bunch of frequencies competing for attention, filters allow desired frequencies while rejecting unwanted ones. Put another way, filters are like Gandalf in J.R.R. Tolkien\u2019s \u201cThe Lord of the Rings\u201d:\n\u00a0\u201cYou shall not pass!\u201d\nDevices today contain as many as 30 to 40 filters to combat interference. The situation is likely to become even more complex with next-generation high-end smartphones requiring even more filters.\nA smartphone with #nofilter is a paperweight.\nFiltering challenges\nFilters are an essential tool for RF design engineers, but they also have their challenges. For starters, filter performance varies with temperature. Filters in today\u2019s devices are subject to average temperatures of 60 degrees Celsius (140 degrees Fahrenheit) or greater, while sitting in a room temperature environment of 25 degrees Celsius (77 degrees Fahrenheit). Filters embedded in the shark fin or roof of a car get even hotter.\nThe hotter the filter, the more difficult it is to isolate certain frequencies \u2013 and the more likely it is for signals to \u201cdrift\u201d into neighboring frequency bands.\n\u00a0\u201cI\u2019m a big fan of static, white noise, party lines and dropped calls,\u201d said no one, ever.\nAs more new bands are assigned closer to existing ones, managing temperature drift is critical. We\u2019re also seeing the proliferation of carrier aggregation (CA) where cellular service providers are combining as many as five carrier channels to increase network performance, and precise filtering is a must.\nThe RF industry is now developing low-drift and no-drift filter technology to solve temperature problems. These surface acoustic wave (SAW) and bulk acoustic wave (BAW) filters are highly stable over temperature changes to meet demanding performance requirements for new and emerging devices.\nAs I mentioned, next-generation high-end smartphones also need more filters. Like everything in RF, there\u2019s a finite amount of real estate for these components. Engineers have had to find ways of combining filters to deliver higher performance in a smaller space.\nEnter some of my favorite terms in the RF dictionary.\nDuplexers, triplexers, quadplexers \u2013 yes, even hexaplexers \u2013 are all part of a class of devices called multiplexers. Multiplexers combine multiple filters into a single device, which helps designers save space, simplify design, and meet performance requirements, while avoiding interference.\nWi-Fi presents a final challenge. While some luddites still use smartphones for texting and calling, most of us spend our time browsing the web, streaming videos and posting to social media. LTE and Wi-Fi bands are extremely close together, and left unfiltered, Wi-Fi signals can desensitize LTE reception on a device. Desensitization causes a slew of dreadful things, including dropped or interrupted calls.\nFor this, we need a special kind of filter.\nCoexistence filters allow Wi-Fi and LTE signals to exist in harmony. The name suits them well. These filters reject closely adjacent frequencies, so we can view our friends\u2019 Instagram stories without missing a call from Mom. They\u2019re also important in the connected car, where LTE, Wi-Fi, Bluetooth, GPS and vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) must coexist without interference.\nWithout filters, we\u2019d have quite the wireless traffic jam.\nIn today\u2019s mobile environment, the number of bands required in one device is staggering\u00a0\u2014\u00a0and the trend will only increase as we approach 5G. Supporting all these bands causes interference issues, requiring filters to save the day. Without filters, networking simply doesn\u2019t work.